PTFE Pleated Micron Membrane Filter Cartridge

Product Description

PTFE Pleated Micron Membrane Filter Cartridge.

Characteristics and features

• Excellent high-tem resistance and extensive chemical compatibility.

• All the compositions reach up to the requirement of the biological testing characteristics of USP Class 6 plastic products at 121ºC and the food contact materials listed in the relevant regulations of Chapter 21 of the Federal Regulations of the United States (CFR). They also conform to the requirements of China's "Standard for Hygienic Safety Evalution of Equipment and Protective Materials in Drinking Water" (2001) for drinking water transport and distribution equipment.

• 99.99995% bacteria retention in gas and liquid.99.99995% of all kinds of phages, bacteria and particles above 0.01μm were retained during gas filtration.

• The sampling of filter element successfully passed the bacterial challenge test required by regulations, LRV≥7.Integrity can be maintained after repeated high-pressure disinfection.

• Each filter element should pass the integrity test before leaving the factory. The limitations of integrity testing were correlated with the results of bacterial challenge experiments.

• It is manufactured under ISO 9001 and ISO 14001 systems and Class 100 environment.

• Production and usage are traceable.

• Resistant to repeated steam sterilization.

• large air flow, high efficiency and small volume
  

  Material of filter element components:
  Filter material : Natural hydrophobic PTFE membrane

  Supports/Diversion : PP

  Core/Cover/End cover/End caps : PP

  Sealed leads/Fins : PP,Built in stainless steel

  O-Ring : 222,226 silicon rubber etc.

  Sealing technology : Hot melt without adhesives

  
  

  Technical specifications and operating parameters

  Size	Diameter: 2.75" (69 mm) Length: 5"/10"/20"/30"/40" etc.
  Filtration Area	Single 10" filter element is about 0.65m²
  Minimum Bubble Point of Integrity Test Data	0.22μm: ≥ 0.13MPa (Import) ≥ 0.1MPa (Chinese) 0.45μm: ≥ 0.06MPa 23°C 60:40IPA: water(V:V)
  Typical Flow Aate	0.1um≥180Nm^3 /h 0.22μm≥330Nm^3 /h 0.45μm≥400Nm^3/h, (P=0.2MPa, ΔP=0.01MPa, 20°C, 10" length)
  Accumulated Steam Sterilization Time	121°C, 100 hours 140°C, 40 hours Under experimental conditions
  Maximum Differential Pressure	Positive:0.4MPa Negative:0.2MPa
  Recommended Service Life for Air Filtration	12 months for 60°C compressed air filtration 6 months for 80°C breathing port filtration

  
  Typical application

• Breathing port filtration of WFI storage tank.

• Air inlet and exhaust filtration of large scale fermentation tank.

• Breathing port filtration of medical intermediate storage tank.

• Filtration of instrument gas in pharmaceutical industry.

• Vacuum barrier of autoclave.

• Transmission and filtration of air and other gases.

• Gas filtration for aseptic packaging.

• Sterilization and filtration of compressed air and CO2 in food and beverage industry.

• Filtration of corrosive chemicals.
  
  Ordering information

   

  1	2		3	4	5	6	7
  PTFE	0.22	---	10	A	S	P	--X

   

  1	Membrane	Hydrophobic / hydrophilic PTFE membrane
  2	Pore size	0.1,0.22,0.45um
  3	Length	5" / 10" / 20" / 30" / 40"
  4	Connector/End Cover A/AA/B/BB/C/CC/D/E/EE/F	Spear+222 Spear+222adapter with encapsulated reinforcing stainless steel ring Flat+222 Flat+222adapter with encapsulated reinforcing stainless steel ring Spear+226 Spear+226adapter with encapsulated reinforcing stainless steel ring Flat+Flat Flat+226 Flat+226adapter with encapsulated reinforcing stainless steel ring Flat+215 Spear+3 Flange Bayonet adapter
  5	Gasket Material S,E,F,FF	S:silicon rubber E:EPDM rubber F:Fluorine rubber FF:Encapsulated fluoroelastomer
  6	Application P	Pharmaceutical grade for bio-pharmaceutical&food and beverage industry
  7	Special Specification Remarks	Standard Specification Default

  Note: The service life of the steam sterilization and other technical parameters are tested under strictly controlled experimental conditions. However, the actual operating conditions and experimental conditions will be different. For the application of a specific process, the performance of the filter needs to be verified and confirmed.