Pes Membrane Micron Pleated Filter Cartridge

Product Description

PES Membrane Micron Pleated Filter Cartridge.

Characteristics and features

• Excellent high-tem resistance and extensive chemical compatibility.

• All the compositions reach up to the requirement of the biological testing characteristics of USP Class 6 plastic products at 121ºC and the food contact materials listed in the relevant regulations of Chapter 21 of the Federal Regulations of the United States (CFR). They also conform to the requirements of China's "Standard for Hygienic Safety Evalution of Equipment and Protective Materials in Drinking Water" (2001) for drinking water transport and distribution equipment.

• The sampling of filter element successfully passed the bacterial challenge test required by regulations, LRV≥7.Integrity can be maintained after repeated high-pressure disinfection.

• Each filter element should pass the integrity test before leaving the factory. The limitations of integrity testing were correlated with the results of bacterial challenge experiments.

• It is manufactured under ISO 9001 and ISO 14001 systems and Class 100 environment.

• Low protein adsorption to make sure the maximum recovery of target active ingredients.

• The filter membrane has a gradient aperture structure for pre-filtration with large flow rate ,low pressure difference and long service life .

• Production and usage are traceable.
  
  

  Material of filter element components:
  Filter membrane : Hydrophilic PES membrane

  Support/Drainage : PP

  Core/Cover/End cover/End caps : PP

  Sealed leads/Fins : PP with stainless steel inside

  O-Ring : 222,226 silicon rubber etc.

  Sealing technology : Thermal bonding without adhesives
  

  Technical specifications and operating parameters

   

  Size	Diameter: 2.75" (69 mm) Length: 5"/10"/20"/30"/ 40" etc.
  Filtration area	Single 10" filter element is about 0.65m²
  Dissolution(20ºC)	Testing The filters without pre-washing . After 24 hours immersion in water, the dissolution was less than 30 mg/10" filters.
  Minimum Bubble Point of Integrity Test Data	0.1  μm: > 0.38  MPa in Water 0.22 μm : > 0.32  MPa in Water 0.45 μm: > 0.20  MPa in Water
  Conditions of steam sterilization and hot water sterilization	Sterilization temperature: hot water 85ºC Steam 121 ºC/30 min, more than 15 times
  Maximum pressure difference and temperature	Maximum operating temperature: 85ºC/0.2 MPa;  25 ºC (≥ 0.4 MPa)
  Typical flow rate (Water, 20ºC)	0.1 um: 4 lpm/0.01MPa/10" 0.22 um: 10 lpm/0.01MPa/10" 0.45 um: 15 lpm/0.01MPa/10"

  
  
  Ordering information

   

  1	2		3	4	5	6	7
  PES	0.22	---	10	A	S	P	--X

  1	Membrane	Hydrophilic PES
  2	Pore size	0.04 / 0.1 / 0.22 / 0.45 μm
  3	Length	5" / 10" / 20" / 30" / 40"
  4	Connector/End Cover A/AA/B/BB/C/CC/D/E/EE/F	Spear+222 Spear+222adapter with encapsulated reinforcing stainless steel ring Flat+222 Flat+222adapter with encapsulated reinforcing stainless steel ring Spear+226 Spear+226adapter with encapsulated reinforcing stainless steel ring Flat+Flat Flat+226 Flat+226adapter with encapsulated reinforcing stainless steel ring Flat+215 Spear+3 Flange Bayonet adapter
  5	Gasket Material S,E,F,FF	S: Silicon rubber E: EPDM rubber F: Fluorine rubber FF: Encapsulated fluoroelastomer
  6	Application P	Pharmaceutical grade for bio-pharmaceutical&food and beverage industry
  7	Special Specification Remarks	Standard Specification Default